how to clean mass air flow sensor chevy equinox

If you have a hot wire mass air flow sensor make sure the cleaner doesnt get onto the hot wires or plate. Unplug the electrical connector from the mass airflow sensor.

2018 2022 Chevrolet Equinox Maf Sensor Replacement Guide 016

Some folks recommend using alcohol because its usually on hand and can clean the sensor.

. Push in on the tabs of the connector and unplug it from the MAF sensor. Remove the sensor from the housing. Chevrolet 2005 equinox 34l v6 exhaust emission mass air flow maf sensor.

Remove the entire air mass sensor. Often the mass airflow sensor really only needs cleaning when they go bad. Now well proceed to the very delicate cleaning of the flow meter filaments.

Then let the cleaner sit for few seconds. If you are too afraid of harming it you can also clean them with a brake fluid in the form of an. Itll have a large electrical connector plugged into it.

You have to be very careful otherwise your mass air flow sensor will be permanently broken. Remove the mass air flow sensor from the car or truck. 3 Symptoms of a Faulty Mass Air Flow Sensor.

Cleaning the Mass Airflow Sensor. If you see Torx screws buy a Torx tool and a can of CRC Mass Air. Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air dry for an hour or until completely dry.

With the Chevy Equinox P0101 means the the Mass Air Flow MAF sensor has a RangePerformance problem. Locate and disconnect the MAF sensor. Place the sensor on a towel for cleaning.

This is a bad idea it can ruin the sensor. With the help of a fine brush and solvent gently clean the. Mass air flow MAF sensors measure the amount of air entering the engine.

Now well proceed to the very delicate cleaning of the flow meter filaments. Youll see it just down from the large air intake box on the far left. Remove The MAF Sensor From Vehicle.

Its really cheap and available at any parts store. It should be considered a high priority to fix as the MAF sensor not reading properly can really make an impact on the performance of the vehicle. Reliable and quiet your Chevrolet Equinox small crossover SUV is perfect for highway driving and it gets respectable gas mileage as well.

We recommend that you clean the MAF sensor every time you change your air filter. Also clean the sides of the part its housing its connectors and its terminals. And lets get started with the actual step by step cleaning of the GM mass air flow MAF sensor Buick Chevrolet Oldsmobile Pontiac and GMC models.

The OEM sensor was marked with a few sets of part numbers including AFH70M-124 7Y30 HALF 23366103 and 79300JI. Now take out your Mass airflow sensor cleaner and spray it inside of the sensor. Uses mass airflow sensor cleaner.

If you are too afraid of harming it you can also clean them with a brake fluid in the form of an aerosol by spraying the jet on these filaments. Look for the little black box attached to the air intake hose. Clean your dirty mass air sensor.

Remove the screws that hold the mass airflow sensor in place. You have to be very careful. It sure beats the heck out of.

After removing the mass airflow sensor make sure not to touch or damage any sensor elements. With the help of a fine brush and solvent gently clean the two filaments of your mass air flow sensor. Step 4 Clean your dirty mass air sensor.

We will cover exactly what that means and potential fixes for it below. Unplug the electrical connector. You have to be very careful in any other case your mass air flow sensor will be permanently damaged.

Do not spray too much and spray twice or thrice at a time. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone. Spray 2 to 3 bursts of sensor cleaner onto the map sensor.

The genuine GM compatible replacement mass air flow sensor part number is ACDelco 23366103. Step 1 Remove the MAF sensor. Reinstall and test drive.

Before going to the store pull off the air duct between the air filter box and the throttle body to see how the MAF sensor is anchored. 1 How does a MAF sensor work. MAF Sensor Cleaner on Amazon.

Now well proceed to the very delicate cleaning of the flow meter filaments. And let s get started with the actual step by step cleaning of the gm mass air flow maf sensor buick chevrolet oldsmobile pontiac and gmc models. Httpsamznto2Wc7XESHow To Clean Mass Air Flow MAF Sensor in Chevrolet Colorado GMC Canyon Hummer H3In this video I am sh.

Apply the cleaner 10-15 blasts around the inside of the sensor will do. Then apply the solvent to the wire mesh on the front of the sensor and scrub in a circular motion with an emphasis on any oil residue that may be present. Start by opening the hood.

Alright enough of the bs. Find the location of the MAF sensor in your Equinox it will be somewhere between the air filter box and the throttle body. 2 How To Clean Mass Air Flow Sensor Chevy Silverado 2004-2006 21 Step 1.

With the help of a fine brush and solvent delicately clean the two filaments of your mass air flow sensor. Press the red clip slightly to unlock it. Once off your MAF sensor should look like the one in the photo.

If you would like to try cleaning your old MAF sensor before buying a new one carefully spray the sensor wire with some CRC Mass Air Flow Sensor Cleaner. The mass air flow cleaner only costs about 7. Open the hood of your Chevrolet.

Locate the mass airflow sensor near the engine air filter housing. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will take out most of the grime. If you like you can also spray down the sensor with some WD-40.

How to clean mass air flow sensor chevy equinox. The hood release is located under the dashboard on the drivers side. To clean your MAF sensor simply take a solvent and spray it onto a paper towel.

How To Replace Air Flow Meter Sensor 10 12 Gmc Terrain Youtube